1-800-523-5204 or 1-937-294-6261
Bevel Ball Actuators BB300 (35 Ton)
BB300
Joyce BB300 bevel ball actuators with a 35-ton static capacity, offer higher efficiency and greater speed than other mechanical screw jacks. These are among Joyce’s fastest jacks, able to attain travel speeds of 27.3 feet per minute. Available in Translating and KFTN designs, they act as miter boxes, making them an ideal choice for multi-jack systems. As many as three output shafts may be specified for mounting motors, limit switches, readout devices and other accessories.
- 3” diameter lifting screw
- Require a brake or other external locking device to hold position
- Fully predictable J-10 ball nut life expectancy
- Right hand screws standard (left hand screws available)
- Threaded end conditions standard (load pad, clevis, and plain end conditions available)
- Load capacity is dependant on configuration
Click here for 2D & 3D
Print
- Ductile iron housing
- Alloy steel ball screw
- Aluminum bronze traveling nut (KFTN)
- Input shaft CDS
Sample Part Number:
Click on the part number to reveal additional informaton about actuator designs and shaft codes.
| Joyce Bevel Ball Actuators |
|---|
| BB150 |
| BB225 |
| BB300 |
| BB400 |
Actuator Configuration
| Actuator Configuration | ||
|---|---|---|
 |
 |
|
| U= Upright | I= Inverted | |
End Conditions
| End Conditions | |||
|---|---|---|---|
 |
 |
 |
 |
| 1 = T1 (plain end) | 2= T2 (load pad) | 3= T3 (threaded end) | 4= T4 (male clevis) |
Actuator Design
| Actuator Design | ||
|---|---|---|
 |
 |
 |
| S= Translating | Keyed for Non Rotation is not a standard option | N= Travelling Nut |
Bevel Ball Actuator Rise
| Bevel Ball Actuator Rise |
|---|
| Rise is travel expressed in inches and not the actual screw length |
| Shaft Codes |
|---|
| Three shaft codes must be specified for each jack. Electronic and mechanical limit switches may be substituted for the shaft code per the tables on this page. |
| STDX- Standard |
| XXXX- Input shaft no required |
| When ordering with only one input shaft, it is recommended to order the following configuration: XXXX-STDX-XXXX |
| Additional Options |
|---|
| X= Standard Actuators, no additional options |
| X= Additional Specification Required (comment as necessary) |
| Protective Boots |
| B= Protective Boot |
| D= Dual Protective Boot |
| Finishes |
| F1= Do Not Paint |
| F2= Epoxy Paint |
| F3= Outdoor Paint processes |
| Ball Screw |
| L= Left hand Screw |
| Screw Stops |
| Extending stops standard (specify as many options as needed) |
| Model | Dynamic Capacity | Upright Assembly: Screw-in tension | Upright Assembly: Screw-in compression | Screw Dia./Lead | Bevel Gear Ratio | Pinion Turns for 1" Travel | Pinion Torque (Raising) | Pinion Torque (Holding) | Screw Torque | Actuator Efficiency | Base Weight (Lbs.) | Add for Each Inch of Travel (Lbs.) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| BB300 | Please use JAX® V2 software or contact Joyce/Dayton | 42,500 lbs. | 70,000 lbs. | 3.75/.66 | 3.52:1 | 5.34 | .044W* | .035W* | .117W* | 72.2% | 360 | 3.2 |
| Inverted Assembly: Screw-in tension | Inverted Assembly: Screw-in compression | |||||||||||
| BB300 | Please use JAX® V2 software or contact Joyce/Dayton | 70,000 lbs. | 42,500 lbs. | 3.75/.66 | 3.52:1 | 5.34 | .044W* | .035W* | .117W* | 72.2% | 360 | 3.2 |
Important Note: Bevel Ball Actuators are not self-locking. Brake motors or external locking systems are required.
*W: Load in Pounds.
Pinion Torque (raising): The torque required to continuously raise a given load.
Pinion Torque (holding): The torque required to hold a given static load in position.
Screw Torque: The torque required to resist screw rotation (translating design) and traveling nut rotation (KFTN design).
Lead: The distance traveled axially in one rotation of the lifting screw.
Pitch: The distance from a point on the screw thread to a corresponding point on the next thread, measured axially.